Graphite Design Pershing 65
Designed to match the swing profiles of a variety of players, four Pershing models (45, 55, 65, and 75) are offered in weights ranging from an ultra-light 45 grams up to 79 grams. All models feature a high balance point for superb feel from hands through clubhead. The Pershing line provides a perfect match for today's largest clubheads, but the wide variety of shaft weights and two available tip diameters make it suitable for any size driver or fairway wood. With the combinations of low-to-mid kick points and torque ranging from 3.0 to 6.0, there is a Pershing shaft available for a variety of players that will optimize proper launch angles and spin characteristics.
| Pershing 65 |
| Shaft Type |
Flex |
Length
(inch) |
Weight
(gram) |
Tip size
(inch) |
Butt size
(inch) |
Parallel Tip
Length |
Torque
(degree) |
Kick point |
MSRP |
|
| Pershing 65 |
R |
46.0" |
68 |
.335"&.350" |
.600" |
4.0" |
3.7 |
LOW/MID |
$120.00 |
| Pershing 65 |
S |
46.0" |
69 |
.335"&.350" |
.600" |
4.0" |
3.7 |
MID |
$120.00 |
| Pershing 65 |
X |
46.0" |
73 |
.335"&.350" |
.600" |
4.0" |
3.7 |
MID/HIGH |
$120.00 |
Pershing, YS+, Purple Ice, Prototype Model, TOUR AD (45.0"- 47.0")
| Types |
Products |
Through- Bore |
Blind-Bore |
Std-Bore |
| Drivers |
Pershing 55, 65, 75
YS-5+, YS-6+, YS-7+
PI-55, PI-65, PI-75, PI-85
Prototype Model 702, 902 |
0.0" |
0.5" |
1.0" |
| Pershing 45 |
Insert 2.0" only |
Butt Trim Only |
| Quattro Tech, Tour AD I-65, W-60, W-70 |
Insert 2.0" only |
0.0" |
0.0" |
| #3 Wood |
Pershing 55, 65, 75
YS-5+, YS-6+, YS-7+
PI-55, PI-65, PI-75, PI-85
Prototype Model 702, 902 |
0.5" |
1.0" |
1.5" |
| Pershing 45 |
Insert 2.0" only |
Butt Trim Only |
| Quattro Tech, Tour AD I-65, W-60, W-70 |
Insert 2.0" only |
0.5" |
0.5" |
| #5 Wood |
Pershing 55, 65, 75
YS-5+, YS-6+, YS-7+
PI-55, PI-65, PI-75, PI-85
Prototype Model 702, 902 |
1.0" |
1.5" |
2.0" |
| Pershing 45 |
Insert 2.0" only |
Butt Trim Only |
| Quattro Tech, Tour AD I-65, W-60, W-70 |
Insert 2.0" only |
0.5" |
1.0" |
Notes
- Graphite Design encourages consulting a PGA Professional or qualified clubmaker on selecting the best length shaft for your swing characteristics.
- Tip trimming is dependent on the bore depth and intended results.
- Tip trimming will increase frequency, tip stiffness and torque (amount of increase will vary depending on model.
- Always leave at least .5" of parallel tip section outside the hosel. For example: With a hosel depth of 1.5" and parallel tip length of 4", the trim should not exceed 2".
- Improper installation may affect the intended performance of the shaft.
- Warranty is for material and workmanship of products. Improper installation voids warranty of product.
|
Order Status